Skip to content
Fix iPhone Speaker

Fix iPhone Speaker

Water in the speaker? Press Start. A 165 Hz water eject sound pushes the droplets out of the grille in 45 seconds — the same trick the Apple Watch uses. Works on Android too.

0% Ready

Hold the phone speaker-down. Volume to maximum. Silent switch off.

  1. 1. Volume to max. iPhone: flip the silent switch to ring, or the tone is muted.
  2. 2. Speaker facing down. Gravity does half the work. Hold it over a towel.
  3. 3. Run 45 s, repeat. Works best while the speaker is still wet.

How to fix water in an iPhone speaker

  1. Turn the volume all the way up. On iPhone, flip the silent switch to ring — while it shows orange, web audio is muted and nothing will happen.
  2. Take off headphones and unpair earbuds. If AirPods are connected, the tone goes to them instead of the phone speaker — painfully.
  3. Hold the phone speaker-down. The bottom speaker is next to the charging port; the top speaker is the earpiece slot above the screen. Point whichever is muffled at the floor, over a towel.
  4. Press Start and wait 45 seconds. You may see tiny droplets appear on the grille or the towel. That is the water leaving.
  5. Play a song to test. Still muffled? Press Run again. Try Vibrate mode on the third run.
  6. Then leave it. After three runs, air-dry for 30 minutes and try once more. Do not use a hairdryer, and do not put it in rice.

Works best right after the phone got wet, while the water is still liquid. Dried mineral residue does not vibrate out.

A free speaker cleaner for iPhone, Android and AirPods

Fix iPhone Speaker is a free water eject tool that runs in your browser. Press Start and it plays a 165 Hz water eject sound through your phone’s speaker for 45 seconds. That tone makes the speaker diaphragm move hard enough to push trapped water out through the grille — the same thing the Apple Watch does when you turn the crown after a swim. There is no app to install, no account, no subscription and no advert. It works as an iPhone speaker cleaner, an Android speaker cleaner, and, with the settings changed first, an AirPods water eject tool.

Fix my speaker, water eject, speaker cleaner — same tool

People arrive here with different words for the same problem: “fix my speaker”, “iPhone water eject”, “sound to clear speakers on iPhone”, “clear speaker sound”, “water removal sound”. They all mean one thing — a tone that gets water out of a phone speaker — and the honest answer to all of them is the 165 Hz water eject sound above. There is no separate “fix my speaker” tool and no different “clear speaker” sound; the frequency that clears water is the frequency that clears water.

When to use it

Use it when your iPhone speaker sounds muffled, quiet or crackly after it got wet: a dropped call in the sink, a run in the rain, a shower playlist, a pool photo. Water sits in the tiny holes of the speaker mesh and does not drain on its own, because surface tension holds each droplet in place. Until it comes out, every sound is played through a film of water. The tone breaks that surface tension and, with the speaker facing down, gravity does the rest. If you need to fix an iPhone speaker after getting it wet, this is the first thing to try, before you book a repair or wait days for it to dry.

Sound mode and Vibrate mode

Sound plays the tone continuously: 165 Hz as the fundamental, with harmonics so it is loud enough on a small phone speaker. Vibrate pulses the same tone on and off, which makes the phone body buzz and gives a stubborn droplet a series of shoves rather than one steady push. Start with Sound. If the speaker still sounds wet after two runs, switch to Vibrate for the third.

Top speaker, bottom speaker, ear speaker

An iPhone has two speakers, and the tone plays through both. The bottom speaker sits beside the charging port and carries music, videos and speakerphone. The top speaker — the earpiece, or ear speaker — is the slot above the screen and carries phone calls. If calls sound muffled but music is fine, it is the top speaker that got wet: hold the phone screen-down with the top edge toward the floor. If music is muffled, hold it upright with the port facing down. Android phones usually have the same two, in the same places.

What about dust?

Honestly: a speaker cleaner sound is a water tool first. Loose dust that is sitting on the mesh may shake free during a run, and you will sometimes see it on the towel. Compacted pocket lint will not vibrate out, whatever a “speaker dust cleaning sound” claims. For that, use a soft dry toothbrush across the grille, or press a small piece of Blu-Tack on it and lift. Never poke the holes with a pin, and never blow canned air into them — both push debris deeper and can tear the mesh.

What about the charging port?

Sound does nothing for the charging port, because there is no speaker inside it to vibrate. Tools that promise to eject water from the port with a tone are selling the speaker trick under the wrong name. If your phone says “liquid detected”, the fix is patience and gravity — the charging port guide covers it step by step, including the pocket-lint problem that causes most false warnings.

Why it is free and why it is safe

The tone is generated by the Web Audio API in your browser, so pressing Start never sends anything anywhere — the only script that talks to a server is Google Analytics, which counts page visits and nothing about how you use the tool (details). It is safe for the speaker because it is a normal-volume tone that stops itself after 45 seconds; the only real risk is running it with headphones on, which is why the tool asks you to confirm you have taken them off. Free, because a wet speaker is a two-minute problem and should not cost a subscription.

Speaker cleaner for every device

Does this really work?

Yes, for water in the speaker — and it is the same trick your smartwatch uses. A speaker is a paper-thin diaphragm on a coil. At 165 Hz the diaphragm of a phone speaker moves close to its largest excursion, so each cycle gives the water droplets sitting in the mesh a physical shove. Water only stays in the grille because of surface tension; a few hundred shoves a second break it, and the droplets get pushed out through the holes. Hold the speaker facing down and gravity finishes the job.

Apple Watch’s Water Lock does exactly this — it plays a tone and you can watch the droplets leave the grille. Samsung Galaxy Watch and several Android phones (OnePlus, Xiaomi) ship the same feature under “speaker cleaner”. This page just gives every phone the button.

What it does not do

  • Charging port. Sound does nothing there — the port has no diaphragm. Playing a tone over a “liquid detected” warning is wasted time. What actually works for the port.
  • Dust and lint. Loose dust may fall out during a run, but compacted pocket lint does not. For that, a soft dry toothbrush or a piece of Blu-Tack pressed gently on the grille beats any sound.
  • A blown speaker. If the sound is crackly and quiet without the phone ever getting wet, the voice coil is damaged. No tone fixes hardware.

Why this and not an app

The tone is generated by your browser’s Web Audio API with a 165 Hz fundamental — not a compressed MP3. It is deliberately not a bare sine: a phone speaker can barely reproduce a lone 165 Hz sine, so the wave carries its odd harmonics too, which is what makes it loud enough to matter while 165 Hz stays the strongest component. There is no app to install, no account, no subscription and no ads. Google Analytics counts page visits; what you do with the tool never leaves your device. It is free because there is nothing to sell.

Do not run the tone over and over on a speaker that is already dry. Pushing a dry diaphragm at full volume for minutes on end can loosen the voice coil and leave a permanent rattle. Three runs, then let it air-dry.

Fix iPhone speaker — questions people ask

How can I remove water from my iPhone speakers?
Turn the volume to maximum, flip the silent switch to ring, hold the iPhone with the wet speaker facing down, and press Start above. The 165 Hz water eject sound vibrates the speaker for 45 seconds and pushes the droplets out of the grille. Play a song to check; if it is still muffled, press Run again. Most iPhones clear in one to three runs.
What sound can I use to remove water from my iPhone speakers?
A low tone around 165 Hz. That is the frequency the Apple Watch Water Lock uses and the one people on Reddit report working most consistently, because it sits near the resonance of a phone speaker diaphragm. This page generates that 165 Hz water eject sound in your browser, so you do not need a YouTube video, an app, or a Shortcut.
Do iPhones have water eject?
No. Water eject is a built-in Apple Watch feature (Water Lock); the iPhone has never had a native button for it. iOS only shows a “liquid detected” warning for the charging port. People who remember an iPhone water eject used a Siri Shortcut. This tool does the same job from Safari with nothing to install.
How to activate water eject on iPhone?
On an Apple Watch: swipe up to Control Center, tap the water drop, then turn the Digital Crown. On an iPhone there is nothing to activate — open this page, remove any headphones, set volume to maximum, hold the speaker down and press Start. Sound mode first; Vibrate mode for a stubborn droplet.
How to eject water from iPhone 13?
Same as every iPhone since the 7: silent switch to ring, volume to maximum, speaker facing down, press Start for 45 seconds. The iPhone 13 has the bottom speaker beside the Lightning port and the earpiece in the notch; point whichever is muffled at the floor. It works identically on iPhone 11, 12, 14, 15, 16 and 17.
How to fix iPhone speaker after dropping it in water?
First, dry the outside and do not charge it. Then run the water eject sound with the speaker facing down, two or three times. Leave the phone in a dry room for a few hours — the speaker will clear faster than the charging port. Skip the rice and the hairdryer; both do more harm than open air. If the speaker was fine before the dunk, this fixes it in the large majority of cases.
How to fix iPhone speaker water damage?
If the speaker got wet recently, it is usually not damage — it is water sitting in the mesh, and the tone above clears it. Real water damage means the sound stays crackly or quiet after the phone has been fully dry for 24 hours. At that point the speaker (or, for salt water, the corroded contacts) needs replacing by Apple or a repair shop.
Does water permanently damage iPhone speakers?
Rarely, if you clear it quickly. Every iPhone since the 7 is water resistant, and a wet speaker is just a wet membrane. Permanent damage happens when the water is salty, sugary or left for days — residue stiffens the diaphragm and corrodes the coil. Clean water pushed out within the hour almost never leaves a mark.
How do I unclog my iPhone speaker?
It depends on what is clogging it. Water: run the tone above with the speaker facing down. Dust and pocket lint: brush the grille gently with a soft, dry toothbrush, or press a small piece of Blu-Tack on it and lift — loose dust may also fall out during a run, but sound cannot pull out compacted lint. Never poke the grille with a pin or blow canned air into it.
How to fix a muffled speaker on iPhone?
Muffled after water is the easy case: run the water eject sound until it clears. Muffled with no water involved: check that the case or a screen protector is not covering the grille, brush out lint, turn off Reduce Loud Sounds in Settings → Sounds & Haptics, and restart the phone. If it stays muffled after all that, the speaker is failing.
How to fix iPhone speaker crackling?
Crackling right after the phone got wet is water on the diaphragm — run the tone, speaker down, two or three times, then let it dry. Crackling on a dry phone at high volume usually means debris on the cone or a torn diaphragm: try the tone once, clean the grille, and test with a different app. If every app crackles at the same volume, the speaker needs replacing.
iPhone speaker sounds distorted — how do I fix it?
Restart the phone and test with a different app first; distortion in one app is a software issue. If it is every app: run the water eject sound in case moisture is trapped, then brush the grille. Turn off any EQ in Settings → Music. Distortion that survives all of this, on a dry phone, is a damaged speaker.
How to fix the top speaker on iPhone?
The top (earpiece) speaker is the thin slot above the screen. It gets muffled from water, from pocket lint, and from a screen protector cut too tight. Hold the phone screen-down, top edge toward the floor, and run the tone. Then clean the slot with a soft brush and check the protector is not covering it. Calls quiet but music fine is the classic earpiece symptom.
How to get water out of the iPhone speaker without an app?
This page. It is a website, not an app — nothing to install, no account, no subscription. The tone is generated by Safari itself. Open it, remove headphones, volume to maximum, speaker down, press Start.
How much does it cost to fix an iPhone speaker?
Nothing, if the problem is water — the tone above is free. If the speaker is physically damaged, Apple treats it as out-of-warranty “other damage”, which on recent models runs well into three figures, while independent repair shops typically charge less for a speaker swap. Run the tone and let the phone dry fully before paying anyone; most “broken” speakers after a spill are just wet.
Is the speaker cleaner sound safe for my iPhone?
Yes, in short runs. It is a tone at the volume your iPhone already plays music, and it stops automatically after 45 seconds. The only way to cause harm is to blast a dry speaker at full volume for many minutes, or to run it with headphones on — which is why the tool makes you confirm you have removed them.
Does the water eject sound work on Android?
Yes. The physics is the same for every phone speaker, so the tone works on Samsung, Pixel, OnePlus and every other Android phone. Some Android phones (OnePlus, Xiaomi) even hide a built-in speaker cleaner in settings; this page gives every phone the same button from the browser.
Will it remove water from the charging port?
No, and no sound-based tool can — the port has no speaker to vibrate. If you see “liquid detected”, follow the charging port guide: power off, tap it port-down, and give it time.